Fittings

A range of connectors, adapters, clamps and valves to suit any arrangement.

Connector Straight 1/4"M to 8 x 1

The standard connector as fitted to most components.

CONN-179
Weight: 32.00 gms

Connector Rt. Angle 1/4"M to 8 x 1

A right angled version of the above. Use to improve tubing runs.

CONN-180
Weight: 40.00 gms

Connector Straight 1/8"M to 8 x 1

A straight connector for a 1/8" BSP aperture.

CONN-627
Weight: 35.00 gms

Connector Rt. Angle 1/8" to 8 x 1

A right angled connector for 1/8" BSP apertures.

CONN-628
Weight: 40.00 gms

Connector Top Outlet 1046/HPPS 8 x 1

The standard top outlet connector for the Eheim 1046/HPPS pump.

CONN-512
Weight: 30.00 gms

Connector Top Outlet 1048 8 x 1

The standard top outlet connector for the Eheim 1048 pump.

CONN-513
Weight: 34.00 gms

Connector thru Bulkhead 2 x 8 x 1

Fits either side of the case wall. Tubing can then be fitted both sides.

CONN-501
Weight: 45.00 gms

Connector Inline Rt. L' 2 x 8 x 1

Use where a tight bend cannot be avoided towards the centre of a tubing run.

CONN-500
Weight: 30.00 gms

Adapter Top Outlet 1046/HPPS 1/4"F

Allows the fitting of another connector to the outlet of the 1046/HPPS pump. Usually a right angled connector (CONN-180) for clearance reasons. Or connectors for 3/8" or 1/2" tubing.

CONN-202
Weight: 17.00 gms

Adapter Top Outlet 1048 1/4"F

Allows the fitting of another connector to the outlet of the 1048 pump. Usually a right angled connector (CONN-180) for clearance reasons. Or connectors for 3/8" or 1/2" tubing.

CONN-252
Weight: 20.00 gms

Adapter Inlet 1046/48/HPPS 1/4"F

Fit to the inlet of the Eheim pump range when a remote header tank is used. Requires a connector CONN-179 or 180. Or use CONN-15 or CONN-16 for 3/8" and 1/2" tube sizes.

CONN-394
Weight: 37.00 gms

Connector Tee 1/4"M to 2 x 8 x 1

Fit where twin circuits are used.

CONN-502
Weight: 43.00 gms

Mini Valve 2 x 1/4"F

A simple shut off valve. Requires connectors - CONN-179 and/or 180.

CONN-503
Weight: 113.00 gms

Quick Release Coupling M/F pair

When released, ensures no loss of fluid. Sold as a male and female pair. Requires connectors CONN-179 and/or CONN-180, one at each end.

CONN-417/8
Weight: 19.00 gms

Connector Straight 1/4" BSPT to barb

This Nylon fitting is used to connect innovatek components to 3/8" or 1/2" tubing.

You may use a sealant, such as PTFE tape. Do NOT overtighten.

CONN-15
Weight: 4.00 gms

Connector Rt.Angle 1/4" BSPT to barb

Use instead of items CONN-15/3 & 4 above to give a better tube run. Available in blue nylon only.

Note: If the connectors are too close, such as on a waterblock, then you can only fit one of these items.

You may use a sealant, such as PTFE tape. Do NOT overtighten.

CONN-16
Weight: 5.00 gms